Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Missouri City Owner’s Guide

Ghost Controls keypad and intercom repair in Missouri City typically runs between $160 and $390 installed, depending on whether we’re replacing the keypad face, the control board, or the full wired entry station. Most jobs are completed the same day we arrive, and we stock Ghost Controls-compatible keypads, intercom modules, and wiring harnesses on our service trucks. The way owners usually discover the failure is simple: the keypad lights up but the gate won’t move, or the intercom rings the house but no voice comes through, or the buttons work intermittently after rain.

Call (346) 253-1761

You’re not imagining the rain connection. Missouri City’s humidity and afternoon thunderstorms are hard on outdoor keypads, especially the membrane-style buttons Ghost Controls uses on their AXS and DTP series. We’ll get into exactly what fails and why below.

Which Ghost Controls Models This Applies To

Ghost Controls built its reputation on the automatic gate opener retrofit market, and two lines dominate Missouri City driveways: the AXS series (solar-friendly, single or dual gate, sold in kits) and the R series / DTP series for heavier swing and slide gates. The keypads and intercoms across these lines share the same four-wire communication protocol, but the mounting plates and enclosure sizes differ. A keypad from an R-series kit will not drop into an AXS plate without an adapter bracket.

Here’s the compatibility gotcha most owners miss: Ghost Controls keypads are not interchangeable with the older Ghost-branded units from before the 2018 model year. If your opener arm says “Ghost” but not “Ghost Controls,” or if your keypad has a circular button layout instead of the current rectangular grid, we’ll need the model number off the control board to source the right part. It’s printed on a white label inside the opener housing.

OEM versus aftermarket matters more for Ghost Controls than for some other brands. The OEM keypads are sealed better against moisture and the buttons are UV-stabilized, which matters in Texas sun. We stock OEM Ghost Controls keypads and quality aftermarket equivalents, and we’ll tell you honestly which one fits your budget and your install. For intercom modules, we lean OEM almost every time, because the two-wire audio circuit is picky about impedance matching.

Signs Your Ghost Controls Keypad & Intercom Is Failing

• Keypad lights up but the gate won’t open: The membrane buttons have worn through or the internal ribbon cable has corroded. This is the most common failure we see in Missouri City, and it almost always traces back to moisture intrusion around the lower edge of the faceplate.
• Intermittent response after rain or heavy dew: Condensation is shorting one of the columns on the keypad matrix. It will often work again once it dries out, but the corrosion is already on the trace, and it will fail permanently within a few months.
• Some buttons work and others don’t: The silicone dome under the dead buttons has collapsed or torn. Partial keypad failure is a clear sign the part is at end of life, not a wiring issue.
• Intercom rings the house but no audio comes through, or audio is one-way: The condenser microphone in the outdoor unit has failed, typically from humidity. Ghost Controls intercom mics are sealed with a foam gasket that degrades after four or five Texas summers.
• Gate opens on its own or keypad enters the access code twice: The anti-tamper switch or the main logic chip is shorted, often from an ant or spider nest inside the housing. We see this more often on properties near the Brazos River floodplain where insect pressure is higher.

Before

After

Replacement Cost & What’s Included

In Missouri City, a Ghost Controls keypad replacement installed runs between $160 and $260, depending on whether we need a standard wired keypad or a wireless keypad with a separate receiver board. A full intercom replacement lands between $240 and $390, including the outdoor station, the indoor handset wiring check, and any necessary weatherproofing. If both the keypad and intercom failed together, we’ll usually quote the pair as a combined job at a discount over doing them separately.

Every price is written down and handed to you before any work starts. That’s Haven Standard Clause 1: have it in writing. The quote includes the part, the labor, the wiring verification, the programming of your access code, and a photo log of what was found, what was replaced, and what the finished install looks like. The 365-Day Done Right Promise covers the keypad and intercom work for a full year, no fine print, no prorating.

DIY or Call Us?

Ghost Controls keypads are low-voltage, so you’re not dealing with the kind of hazard that high-tension gate springs or a 110V control panel present. If the keypad just needs a new access code programmed, the instructions in your owner’s manual will walk you through it in five minutes. If the keypad face is physically cracked but still working, you can replace just the faceplate with a screwdriver and some patience.

What goes wrong with DIY on this part is the wiring. Ghost Controls keypads use a four-wire bus, and one reversed connection can take out the control board on the opener itself, which is a $300 to $500 mistake you don’t want to learn the hard way. The intercom is worse: it’s a two-wire audio circuit that shares the ground with the opener logic, and a short during swap can corrupt the opener’s programming. If you’re not certain which screw terminal is which, call us at (346) 253-1761. We’ll come out, match the part to your specific Ghost Controls model, and leave you with a written record of what we did.

FAQs