Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Fresno, TX
Gate access control and gate parts and welding are the two Fresno specialties we handle most, and the local soil makes both jobs different here than anywhere else. Fort Bend County’s expansive black gumbo clay swells hard after rain and shrinks in summer drought, tilting gate posts and throwing keypads, hinges, and operator arms out of alignment season after season. If your Fresno gate won’t open cleanly or the keypad stopped accepting codes, call (346) 253-1761 and we’ll give you a written price before any work starts.
Why Fresno Homes Are Different
Fresno’s housing stock is almost entirely 2000s-and-newer brick-veneer construction inside HOA-governed subdivisions, where ornamental iron driveway gates and community entry gates went in as tract-builder upgrades. That means technicians here see the same mid-tier automatic operator brands across dozens of adjacent properties: LiftMaster, Apollo, Ghost Controls. The real variable is the ground underneath. Fresno sits on Fort Bend County’s expansive clay, and a gate post poured into a shallow footing will heave back out of plumb within a season no matter how carefully the gate is reset. We dig down and check footing depth before any realignment job here. Hurricane Harvey left a second problem in Fresno: flood-damaged underground conduit and submerged operator housings that were patched rather than replaced, creating electrical failures that surface years later as dead keypads, intermittent remotes, and operators that trip breakers for no visible reason. Hot, humid summers blister powder coat and corrode circuit boards slower than floodwater, but just as reliably.
Our Main Fresno Services
The three jobs below are what most Fresno homeowners reach out for first. Each has its own page with full pricing, local failure patterns, and a breakdown of what happens on site.
Gate Repair in Fresno
Broken hinge? Gate dragging on the driveway? A swing gate that won’t close all the way? Fresno’s clay soil and humid air work against ornamental iron year-round, so most repair calls here are hinge wear, post lean, or operator faults stemming from a gate that stopped swinging true. We diagnose, write the price, and photograph every adjustment before we leave the driveway.
Gate Installation in Fresno
HOA-governed subdivisions in Fresno all have their own material and height rules, and a new gate has to work with whatever operator is already on the property or be paired with a new one. We measure, check the existing footing, and give you a written installation price with a documented record of the job.
Gate Motor & Opener in Fresno
Automatic operators in Fresno fail in predictable ways: burned boards from summer heat, flooded conduits from Harvey, and limit switches knocked out of adjustment when a post shifts. We service nine major brands and replace what’s actually broken rather than steering you toward a full system swap. The Fresno page covers costs and turnaround.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Fresno
Gate access control in Fresno means keypads, remotes, phone entry, card readers, and video intercoms on gates that were mostly installed in the 2000s and are now hitting the end of their first serious maintenance cycle. Humid Gulf Coast air corrodes keypad terminals and circuit boards, and the same clay soil that shifts gate posts also yanks the low-voltage wiring running through underground conduit. When a Fresno gate opens fine from the indoor button but not from the keypad, the problem is usually in the access control wiring or the board, not the motor. We service whatever is on the gate and document every setting and part number, the same way we handle Gate Access Control on every job we do.
Keypad Entry
Signs you need it
Codes that work intermittently, dead keys, or a keypad that lights up but never triggers the gate.
What it costs in Fresno
Keypad replacement in Fresno typically runs $220-$480 depending on brand and whether we can reuse the existing mounting plate and wiring.
How we do it
We bench-test the old keypad, confirm voltage at the operator, install the new unit, program codes, and photograph the final wiring.
Remote Control
Signs you need it
A remote that only works within five feet, a homelink that drops its pairing, or a gate that ignores one of three remotes while the others work fine.
What it costs in Fresno
Replacement transmitters run $45-$90 each, and receiver board replacement is $180-$360 when the operator’s receiver has failed.
How we do it
We match the transmitter to the operator’s frequency, program it on site, confirm range, and log every remote we add to the system.
Video Intercom
Signs you need it
No picture at the indoor monitor, one-way audio, or a call button that rings but never lets you open the gate.
What it costs in Fresno
Video intercom service in Fresno runs $180-$400 for wiring and component fixes; a full replacement with a new monitor is $650-$1,200.
How we do it
We trace the wiring from the outdoor station to the indoor monitor, replace the failed component, and test both audio and video before we leave.
What Gate Access Control Costs in Fresno
| Item | Typical range in Fresno |
|---|---|
| Keypad replacement | $220-$480 |
| Remote transmitter | $45-$90 each |
| Receiver board replacement | $180-$360 |
These are written prices you approve before we start. If your system uses a different access control brand than what’s already on the gate, we’ll give you the figure in the written quote before any work begins.
Can you fix a keypad that stopped working after a rainstorm in Fresno?
Yes. Water in the keypad housing or in the underground conduit is the most common cause we see after heavy Fresno rain. We open the keypad, dry and test the board, and replace the housing seal if water is the problem.
Do you handle HOA-managed entry gates in Fresno?
Yes. We work on community entry gates and individual driveway gates across Fresno’s HOA subdivisions. We provide the photographic record and written report most HOA boards ask for on shared access control equipment.
Gate Parts & Welding in Fresno
Gate parts and welding in Fresno is usually about repairing the gate itself, not the motor: hinges that bind, posts that lean out of plumb, rails that sag, and ornamental iron that has cracked at the welds. Fresno’s expansive clay soil keeps working on these gates long after the builder has left, and we inspect the footing before any realignment because a shallow pour will heave right back out of level. Galvanized and powder-coated iron also ages hard in Fresno’s humidity, so we see a lot of hinge wear and rust-through at the bottom rail. When we weld or replace, we document the part, the material, and the final position, the same way we record work on Gate Parts & Welding every time.
Hinge Replacement
Signs you need it
A gate that sags and scrapes the driveway, or hinges that squeal and show visible metal wear.
What it costs in Fresno
Hinge replacement in Fresno runs $150-$350 per hinge, depending on gate weight and access.
How we do it
We support the gate, cut or unbolt the old hinge, weld or bolt the new one, and check that the gate swings level.
Post Replacement
Signs you need it
A post that leans visibly, a gate that won’t latch, or a gap that opens at the top between gate and post every few months.
What it costs in Fresno
Post replacement in Fresno runs $450-$900 per post including concrete, with deeper footings recommended here for the clay.
How we do it
We dig out the old footing, pour a new one at proper depth, set the post plumb, and rehang the gate after the concrete cures.
Custom Welding
Signs you need it
Cracked ornamental iron, a broken picket, or a section of the gate frame that has separated at a weld.
What it costs in Fresno
Custom welding repairs in Fresno run $120-$250 per weld point, plus materials if we’re adding reinforcement or replacing a section.
How we do it
We grind the cracked area clean, weld the joint, and match the finish as closely as the existing powder coat allows.
What Gate Parts & Welding Costs in Fresno
| Item | Typical range in Fresno |
|---|---|
| Hinge replacement | $150-$350 per hinge |
| Post replacement | $450-$900 per post |
| Custom welding | $120-$250 per weld point |
Can you weld a gate without removing it from the driveway?
Yes, in most cases. We weld in place whenever the gate is stable enough and the repair area is accessible. For structural frame cracks we may need to support or remove the gate first.
How deep should a gate post be in Fresno’s clay soil?
We recommend at least 30 to 36 inches for gate posts in Fresno’s expansive clay, with a wider pour at the base. Shallow footings are the number one reason we see posts lean again within a season.
Brands We Service in Fresno
We maintain and repair Mighty Mule, LiftMaster, FAAC, and BFT systems across Fresno, and we stock common parts for all four locally, which cuts turnaround on keypad, remote, and operator-board replacements. When a part isn’t on the truck, our local supply network usually has it within a day. See our brands for the full list we work on.
Pricing for Gate Repair in Fresno, TX
| Service | Typical range in Fresno |
|---|---|
| Keypad replacement | $220-$480 |
| Remote transmitter | $45-$90 each |
| Receiver board replacement | $180-$360 |
| Video intercom repair | $180-$400 |
| Hinge replacement | $150-$350 per hinge |
| Post replacement | $450-$900 per post |
| Custom welding | $120-$250 per weld point |
| Operator repair (motor replacement) | $500-$850 |
| Operator repair (board/Limit switch) | $175-$350 |
| Operator replacement | $1,200-$2,500 |
Fresno pricing runs slightly higher than average on any job that involves digging: post replacement, conduit repair, and any realignment where the footing has to be redone due to the expansive clay. You get a written, itemized price before we start, and that price doesn’t change unless you approve a change order in writing.
Neighborhoods We Serve in Fresno
We work across Fresno’s HOA subdivisions and unincorporated sections. Response time in the area is typically same day or next morning for gate and access control repairs, depending on parts.
- Teal Run
- Winfield Lakes
- Canyon Gate
- Fresno Estates
- Quail Valley
Service Area - Cities Near Fresno
Fresno sits near several communities we cover with the same written-price and documentation standard. If you’re in one of the cities below, we can usually reach you on the same schedule as a Fresno call.
Missouri City, TX · Manvel, TX · Stafford, TX · Sugar Land, TX
Serving Fresno, TX - Our Local Coverage Area
We’re based in the Fresno area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Fresno
Most Fresno gate repairs are scheduled same day or the next morning. Access control failures and stuck gates take priority, and our live phone line means you talk to a person immediately, not a dispatcher callback.
In most Fresno subdivisions, repairing an existing gate with like-for-like parts doesn’t require HOA approval, but a full gate replacement or color change often does. We can provide the written documentation your management office requests.
Yes. Every Fresno job gets a written, itemized price before any tool leaves the truck. You approve the figure in writing first, and the final invoice matches it unless you request additional work during the visit.
If your gate needs attention in Fresno, call (346) 253-1761. We’ll send a technician, write the price, and leave you with a photo record of everything we touched.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Fresno Customers Say
"The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C.